ZPL Configuration Status to Command Cross-reference
ZPL Configuration Status to Command Cross-reference

ZPL Configuration Status to Command Cross-reference

The Printer Configuration Label, shown below, provides a listing of a majority of the configuration settings that can be set by the ZPL command.
Configuration Label Printout
1
Sensor Settings used for Service Purposes
ZPL Commands and Configuration Receipt Callout Cross-Reference
Command
Listing Name
Description
~SD
DARKNESS
Default: 10.0
^PR
PRINT SPEED
Default: 6 IPS / 152.4 mm/s (max.)
~TA
TEAR OFF
Default: +000
^MN
MEDIA TYPE
Default: GAP/NOTCH
SENSOR TYPE
Default: WEB
SENSOR SELECT
Default: AUTO (
^MNA
- Auto-Detect)
^PW
PRINT WIDTH
Default: 832 (dots)
^LL
LABEL LENGTH
Default: 1225 (dots) (the value constantly recalibrates with automatic Web-Gap detection for label media)
^ML
MAXIMUM LENGTH
Default: 39.0IN 989MM
USB COMM.
Connection Status: Connected / Not Connected
PARALLEL COMM.
Connection Available: BIDIRECTIONAL
^SCa
BAUD
Default: 9600
^SC,b
DATA BITS
Default: 8 BITS
^SC,,c
PARITY
Default: NONE
^SC,,,,e
HOST HANDSHAKE
Default: DTR & XON/XOFF
^SC,,,,,f
PROTOCOL
Default: NONE
SER COMM. MODE
Default: AUTO
CUTTER TYPE
Option Present: LINER/TAG FULL (cut)
^CT
/
~CT
CONTROL CHAR
Default: <~> 7EH
^CC
/
~CC
COMMAND CHAR
Default: <^> 5EH
^CD
/
~CD
DELIM./CHAR
Default: <,> 2CH
^SZ
ZPL MODE
Default: ZPL II
^MFa
MEDIA POWER UP
Default: NO MOTION
^MF,b
HEAD CLOSE
Default: FEED
~JS
BACKFEED
Default: DEFAULT
^LT
LABEL TOP
Default: +000
^LS
LEFT POSITION
Default: +0000
~JD
/
~JE
HEXDUMP
Default: NO (
~JE
)
From this point in the Configuration Receipt listing, the printout has sensor settings and values are displayed to troubleshoot sensor and media operations. These are typically used by Zebra Tech Support to diagnose printer problems.
The configuration settings listed here resume after the TAKE LABEL sensor value. These listings contain printer features seldom changed from default or provide status information (e.g. Firmware Version).
ZPL Commands and Configuration Receipt Callout Cross-Reference
Command
Listing Name
Description
^MP
MODES ENABLED
Default: CWF (See
^MP
Command) (CWFM for wireless printers with display)
MODES DISABLED
Default: (nothing set)
^JM
RESOLUTION
Default:
832 8/mm FULL (203 dpi)
1280 8/mm FULL (300 dpi)
FIRMWARE
Lists ZPL Firmware Version
XML SCHEMA
1.3
HARDWARE ID
Lists Firmware Boot-block Version
CONFIGURATION
CUSTOMIZED (after first use)
RAM
2104k........ R:
OPTION MEMORY
65536k.......B: (only displays this if installed)
ONBOARD FLASH
1536k.........E:
^MU
FORMAT CONVERT
NONE
^JI
/
~JI
ZBI
DISABLED (Requires key to enable)
ZBI VERSION
2.1
^JH
^MA
~RO
LAST CLEANED
X,XXX IN
HEAD USAGE
X,XXX IN
TOTAL USAGE
X,XXX IN
RESET CNTR1
X,XXX IN
RESET CNTR1
X,XXX IN
SERIAL NUMBER
XXXXXXXXXXX
^JH
EARLY WARNING
MAINT. OFF
The printer has the ability to set a command or a group of commands once for all receipts (or labels) that follow. Those settings will remain in effect until they are changed by subsequent commands, the printer is reset, or you restore factory defaults.