ZPL Configuration Status to Command Cross-reference

GK420d Desktop Printer User Guide

The Printer Configuration Label, shown below, provides a listing of a majority of the configuration settings that can be set by the ZPL command.

1	Sensor Settings used for Service Purposes

ZPL Commands and Configuration Receipt Callout Cross-Reference
Command	Listing Name	Description
~SD	DARKNESS	Default: 10.0
^PR	PRINT SPEED	Default: 6 IPS / 152.4 mm/s (max.)
~TA	TEAR OFF	Default: +000
^MN	MEDIA TYPE	Default: GAP/NOTCH
	SENSOR TYPE	Default: WEB
	SENSOR SELECT	Default: AUTO ( ^MNA - Auto-Detect)
^PW	PRINT WIDTH	Default: 832 (dots)
^LL	LABEL LENGTH	Default: 1225 (dots) (the value constantly recalibrates with automatic Web-Gap detection for label media)
^ML	MAXIMUM LENGTH	Default: 39.0IN 989MM
—	USB COMM.	Connection Status: Connected / Not Connected
—	PARALLEL COMM.	Connection Available: BIDIRECTIONAL
^SCa	BAUD	Default: 9600
^SC,b	DATA BITS	Default: 8 BITS
^SC,,c	PARITY	Default: NONE
^SC,,,,e	HOST HANDSHAKE	Default: DTR & XON/XOFF
^SC,,,,,f	PROTOCOL	Default: NONE
	SER COMM. MODE	Default: AUTO
	CUTTER TYPE	Option Present: LINER/TAG FULL (cut)
^CT / ~CT	CONTROL CHAR	Default: <~> 7EH
^CC / ~CC	COMMAND CHAR	Default: <^> 5EH
^CD / ~CD	DELIM./CHAR	Default: <,> 2CH
^SZ	ZPL MODE	Default: ZPL II
^MFa	MEDIA POWER UP	Default: NO MOTION
^MF,b	HEAD CLOSE	Default: FEED
~JS	BACKFEED	Default: DEFAULT
^LT	LABEL TOP	Default: +000
^LS	LEFT POSITION	Default: +0000
~JD / ~JE	HEXDUMP	Default: NO ( ~JE )

From this point in the Configuration Receipt listing, the printout has sensor settings and values are displayed to troubleshoot sensor and media operations. These are typically used by Zebra Tech Support to diagnose printer problems.

The configuration settings listed here resume after the TAKE LABEL sensor value. These listings contain printer features seldom changed from default or provide status information (e.g. Firmware Version).

ZPL Commands and Configuration Receipt Callout Cross-Reference
Command	Listing Name	Description
^MP	MODES ENABLED	Default: CWF (See ^MP Command) (CWFM for wireless printers with display)
^MP	MODES DISABLED	Default: (nothing set)
^JM	RESOLUTION	Default: 832 8/mm FULL (203 dpi) 1280 8/mm FULL (300 dpi)
—	FIRMWARE	Lists ZPL Firmware Version
—	XML SCHEMA	1.3
—	HARDWARE ID	Lists Firmware Boot-block Version
—	CONFIGURATION	CUSTOMIZED (after first use)
—	RAM	2104k........ R:
—	OPTION MEMORY	65536k.......B: (only displays this if installed)
—	ONBOARD FLASH	1536k.........E:
^MU	FORMAT CONVERT	NONE
^JI / ~JI	ZBI	DISABLED (Requires key to enable)
	ZBI VERSION	2.1
^JH ^MA ~RO	LAST CLEANED	X,XXX IN
	HEAD USAGE	X,XXX IN
	TOTAL USAGE	X,XXX IN
	RESET CNTR1	X,XXX IN
	RESET CNTR1	X,XXX IN
—	SERIAL NUMBER	XXXXXXXXXXX
^JH	EARLY WARNING	MAINT. OFF

The printer has the ability to set a command or a group of commands once for all receipts (or labels) that follow. Those settings will remain in effect until they are changed by subsequent commands, the printer is reset, or you restore factory defaults.