Network Setting | Description | |
|---|---|---|
Reset Network | This option resets the wired or wireless (WLAN) print server. You must reset the print server to allow any changes to the network settings to take effect. | |
Related ZPL command(s): | ~WR | |
SGD command used: | device.reset | |
Printer web page: | ||
Primary Network | Specify whether the wired or wireless print server is considered primary. | |
Accepted values: | wired, wlan | |
Related ZPL command(s): | ^NC | |
SGD command used: | ip.primary_network | |
IP Port | This printer setting refers to the port number that the TCP print service is listening on. Normal TCP communications from the host should be directed to this port. | |
SGD command used: | ip.port | |
Printer web page: | ||
IP Alternate Port | This command sets the port number of the alternate TCP port.
Print servers supporting this command will monitor both the primary port and the alternate port for connections at the same time. | |
SGD command used: | ip.port_alternate | |
Printer web page: | ||
Visibility Agent | When the printer is connected to a wired or wireless network, it will attempt to connect to Zebra’s Asset Visibility Service via the Cloud-based Zebra Printer Connector using an encrypted, certificate-authenticated web socket connection. The printer sends Discovery Data and Settings and Alerts Data. Data printed via any label format is NOT transmitted. To opt out of this feature, disable this setting. (For more information, see the “Opting Out of the Asset Visibility Agent” application note at zebra.com.) | |
Accepted values: | on, off | |
SGD command used: | weblink.zebra_connector.enable | |
Printer web page: | ||
IP Protocol (wired or WLAN) | This parameter tells if the user (permanent) or the server (dynamic) selects the IP address. When a dynamic option is chosen, this parameter tells the method(s) by which the wired or wireless print server receives the IP address from the server. | |
Accepted values: |
| |
Related ZPL command(s): | ^ND | |
SGD command used: | Wired: internal_wired.ip.protocol WLAN: wlan.ip.protocol | |
Printer web page: | ||
IP Address (wired or WLAN) | View and, if necessary, change the printer’s IP address. To save changes to this setting, set IP Protocol to PERMANENT, and then reset the print server. | |
Accepted values: | 000 to 255 for each field | |
Related ZPL command(s): | ^ND | |
SGD command used: | Wired: internal_wired.ip.addr WLAN: wlan.ip.addr | |
Printer web page: | ||
Subnet Mask (wired or WLAN) | View and, if necessary, change the subnet mask. To save changes to this setting, set IP Protocol to PERMANENT, and then reset the print server. | |
Accepted values: | 000 to 255 for each field | |
Related ZPL command(s): | ^ND | |
SGD command used: | Wired: internal_wired.ip.netmask WLAN: wlan.ip.netmask | |
Printer web page: | ||
Gateway (wired or WLAN | View and, if necessary, change the default gateway. To save changes to this setting, set IP Protocol to PERMANENT, and then reset the print server. | |
Accepted values: | 000 to 255 for each field | |
Related ZPL command(s): | ^ND | |
SGD command used: | Wired: internal_wired.ip.gateway WLAN: wlan.ip.gateway | |
Printer web page: | ||
MAC Address | View the Media Access Control (MAC) address of the print servers. | |
SGD command used: | Wired: internal_wired.mac_addr WLAN: wlan.mac_addr | |
Printer web page: | ||
ESSID | View and, if necessary, change the Extended Service Set Identification (ESSID) used by the wireless print server. This setting must match the value used by your wireless network. | |
Accepted values: | 32-character alphanumeric string (default 125) | |
SGD command used: | wlan.essid | |
Printer web page: | ||
