Pulse Width Control Commands

Zebra Integrated Multifunction Light Product Reference Guide

Use the commands in this table to control the pulse width by manipulating a digital output. A Fixed Industrial Scanner with Aurora Focus uses these commands to communicate and configure the Zebra Integrated Multifunction Light. If the light is using a different software tool, such as Aurora Design Assistant, the camera and client software can use these commands to communicate with the light.

Software Configuration Commands
Setting	Command	Pulse Duration	Default Value	Max. Value	Description
Job Result	Pass	100	-	-	This command triggers the following peripherals according to their configuration: Status Green - Pass Enable/ Disable - Status Hold Enable/Disable - Status Duration - Status Flashes Speaker - Volume - Tone - Duration Pass Output - Enable/Disable - Polarity - Duration
Job Result	Fail	200	-	-	This command triggers the following peripherals according to their configuration: Status Red - Fai,l Enable/ Disable - Status Hol,d Enable/Disable - Status Duration - Status Flashes Fail Output - Enable/Disable - Polarity - Duration
Status Green	Trigger	300	-	-	This command causes one green flash of the status indicators. The Status Duration value determines the flash duration.
Status Red	Trigger	400	-	-	This command causes one red flash of the status indicators. The Status Duration value determines the flash duration.
Speaker	Trigger	500	-	-	This command causes the speaker to emit one beep,r according to its configuration for Volume, Tone, and Duration.
Speaker	High	600	-	-	This command sets the speaker's sound output volume to 100% of max power.
Speaker Volume	Medium	700	-	-	This command sets the speaker's sound output volume to 50% of max power.
Speaker Volume	Low	800	-	-	This command sets the speaker's sound output volume to 25% of max power.
Speaker Volume	High	900	-	-	This command sets the speaker's sound output to 3367 Hz.
Speaker Tone	Medium	1000	-	-	This command sets the speaker's sound output to 3000 Hz.
Speaker Tone	Low	1100	-	-	This command sets the speaker's sound output to 2673 Hz.
Speaker Duration	Long	1200	-	-	This command sets the speaker's sound output duration to 90 ms.
Speaker Duration	Medium	1300	-	-	This command sets the speaker's sound output duration to 60 ms.
Speaker Duration	Short	1400	-	-	This command sets the speaker's sound output duration to 30 ms.
Status Green	Pass Enable	1500	-	-	This command configures the status indicators to turn on when the job result is a pass.
Status Green	Pass Disable	1600	-	-	This command configures the status indicators to remain off when the job result is a pass.
Status Red	Fail Enable	1700	-	-	This command configures the status indicators to turn on when the job result fails.
Status Red	Fail Enable	1800	-	-	This command configures the status indicators to remain off when the job result fails.
Speaker	Pass Enable	1900	-	-	This command configures the speaker to beep when the job result is a pass.
Speaker	Pass Disable	2000	-	-	This command configures the speaker never to beep when the job result is a pass.
Laser Aimer	Enable	2100	-	-	This command activates the laser aimers. The light ensures that the laser aimers are turned off during the strobe pulse.
Laser Aimer	Disable	2200	-	-	This command deactivates the laser aimers.
Hidden Strobe	Enable	2300	-	-	This command activates the hidden strobe feature.
Hidden Strobe	Disable	2400	-	-	This command deactivates the hidden strobe feature.
Pass Output	Enable	2500	-	-	This command enables the job-pass signal (PASS_OUT) sent by the light when the Job Result: Pass command is received.
Pass Output	Disable	2600	-	-	This command disables the job-pass signal (PASS_OUT) sent by the light when the Job Result: Pass command is received.
Pass Output Polarity	Active High	2700	-	-	This command configures the job pass output (PASS_OUT) to be an active-high signal.
Pass Output Polarity	Active Low	2800	-	-	This command configures the job pass output (PASS_OUT) to be an active-low signal.
Pass Output Duration	Set Duration	2900	10 ms	1000 ms	This command sets the duration of the job pass signal to be equal to the duration of the subsequent pulse.
Fail Output	Enable	3000	-	-	This command enables the job fail signal (FAIL_OUT) to be sent as an output from the light when the Job Result: Fail command is received.
Fail Output	Disable	3100	-	-	This command disables the job-fail signal (FAIL_OUT) from being sent to the light when the Job Result: Fail command is received.
Fail Output Polarity	Active High	3200	-	-	This command configures the job-fail output (FAIL_OUT) as an active-high signal.
Fail Output Polarity	Active Low	3300	-	-	This command configures the job-fail output (FAIL_OUT) as an active-low signal.
Fail Output Duration	Set Duration	3400	10 ms	1000 ms	This command sets the job-fail signal's duration to the subsequent pulse's duration.
Status - Hold	Enable	3500	-	-	This command sets the status indicator lights to hold either green or red, depending on whether the pass or fail, until the next image capture. When enabled, the time per flash and the number of flashes of the status indicators should automatically lock in the UI.
Status - Hold	Disable	3600	-	-	This command disables the Hold Until Next Trigger feature. The time per flash and the number of flashes will determine whether the status indicators show a pass or fail when this feature is disabled.
Status Duration	50 ms	3700	-	-	This command sets the Time per Flash of the status indicators to 50 ms.
Status Duration	100 ms	3800	-	-	This command sets the Time per Flash of the status indicators to 100 ms.
Status Duration	200 ms	3900	-	-	This command sets the Time per Flash of the status indicators to 200 ms.
Status Duration	300 ms	4000	-	-	This command sets the Time per Flash of the status indicators to 300 ms.
Status Duration	400 ms	4100	-	-	This command sets the Time per Flash of the status indicators to 400 ms.
Status Duration	500 ms	4200	-	-	This command sets the Time per Flash of the status indicators to 500 ms.
Status Flashes	1	4300	-	-	This command sets the number of flashes of the status indicators for each job result to 1.
Status Flashes	2	4400	-	-	This command sets the number of flashes of the status indicators for each job result to 2.
Status Flashes	3	4500	-	-	This command sets the number of flashes of the status indicators for each job result to 3.
Status Flashes	4	4600	-	-	This command sets the number of flashes of the status indicators for each job result to 4.
Status Flashes	5	4700	-	-	This command sets the number of flashes of the status indicators for each job result to 5.
Status Flashes	6	4800	-	-	This command sets the number of flashes of the status indicators for each job result to 6.
Pass Output Delay	Set Delay	4900	0 ms	1000 ms	This command sets the delay of the job pass signal to equal the duration of the subsequent pulse - 100us. For example, a pulse of 100us equates to zero delay, and a pulse of 350us equates to a 250us delay.
Fail Output Delay	Set Delay	5000	0 ms	1000 ms	This command sets the delay of the job-fail signal to the duration of the subsequent pulse - 100us. For example, a pulse of 100us equates to zero delay, and a pulse of 350us equates to a 250us delay.