1. ZT211 Industrial Printer User Guide
  2. Printer Configuration and Adjustment
  3. Changing Printer Settings
  4. Other Ways to Change Printer Settings
  5. Calibration and Diagnostic Tools
  • ZT211 Industrial Printer User Guide
Calibration and Diagnostic Tools
View content for :
Product:

Calibration and Diagnostic Tools

Calibration and Diagnostic Tools
Item
Description
Print Information
Print the specified information on one or more labels.
Accepted values:
  • SETTINGS—prints the printer configuration label.
  • NETWORK—prints the settings for any print server that is installed.
  • FORMATS—prints the available formats stored in the printer’s RAM, Flash memory, or optional memory card.
  • IMAGES—prints the available images stored in the printer’s RAM, Flash memory, or optional memory card.
  • FONTS—prints the available fonts in the printer, including standard printer fonts plus any optional fonts. Fonts may be stored in RAM or Flash memory.
  • BARCODES—prints the available bar codes in the printer. Bar codes may be stored in RAM or Flash memory.
  • ALL—prints the previous six labels.
  • SENSOR PROFILE—shows the sensor settings compared to actual sensor readings. To interpret the results, see Sensor Profile.
Related ZPL command(s):
SETTINGS:
~WC
NETWORK:
~WL
SENSOR PROFILE:
~JG
Others:
^WD
Control panel key(s):
SETTINGS and NETWORK: Do one of the following:
  • Hold
    CANCEL
     during printer power-up.
  • Hold
    FEED
     +
    CANCEL
     for 2 seconds when the printer is in the Ready state.
SENSOR PROFILE: Hold
FEED
 +
CANCEL
 during printer power-up.
Printer web page:
View and Modify Printer Settings
Print Listings on Label
Power-Up Action
Set the action for the printer to take during the power-up sequence.
Accepted values:
  • CALIBRATE—adjusts sensor levels and thresholds, determines the label length, and feeds the media to the next web.
  • FEED—feeds the labels to the first registration point.
  • LENGTH—determines the label length using current sensor values, and feeds the media to the next web.
  • NO MOTION—tells the printer not to move the media. You must manually ensure that the web is positioned correctly, or press feed to position the next web.
  • SHORT CAL—sets the media and web thresholds without adjusting sensor gain, determines the label length, and feeds the media to the next web.
Related ZPL command(s):
^MF
SGD command used:
ezpl.power_up_action
Printer web page:
View and Modify Printer Settings
Calibration
Head-Close Action
Set the action for the printer to take when you close the printhead.
Accepted values:
  • CALIBRATE—adjusts sensor levels and thresholds, determines the label length, and feeds the media to the next web.
  • FEED—feeds the labels to the first registration point.
  • LENGTH—determines the label length using current sensor values, and feeds the media to the next web.
  • NO MOTION—tells the printer not to move the media. You must manually ensure that the web is positioned correctly, or press feed to position the next web.
  • SHORT CAL—sets the media and web thresholds without adjusting sensor gain, determines the label length, and feeds the media to the next web.
Related ZPL command(s):
^MF
SGD command used:
ezpl.head_close_action
Printer web page:
View and Modify Printer Settings
Calibration
Load Defaults
Restore specific printer, print server, and network settings back to the factory defaults. Use care when loading defaults because you will need to reload all settings that you changed manually.
Accepted values:
  • FACTORY—Restores all printer settings other than the network settings back to the factory defaults. Use care when loading defaults because you will need to reload all settings that you changed manually.
  • NETWORK—Reinitializes the printer’s wired or wireless print server. With a wireless print server, the printer also reassociates with your wireless network.
  • LAST SAVED—Loads settings from the last permanent save.
Related ZPL command(s):
FACTORY:
^JUF
NETWORK:
^JUN
LAST SAVED:
^JUR
Control panel key(s):
FACTORY: Hold
FEED
 +
PAUSE
 during printer power-up to reset the printer parameters to factory values.
NETWORK: Hold
CANCEL
 +
PAUSE
 during printer power-up to reset the network parameters to factory values.
LAST SAVED: N/A
Printer web page:
FACTORY:
View and Modify Printer Settings
Restore Default Configuration
NETWORK:
Print Server Settings
Reset Print Server
LAST SAVED:
View and Modify Printer Settings
Restore Saved Configuration
Media and Ribbon Sensor Calibration
Calibrate the printer to adjust the sensitivity of the media and ribbon sensors.
For complete instructions on how to perform a calibration procedure, see Calibrating the Ribbon and Media Sensors.
Related ZPL command(s):
~JC
SGD command used:
ezpl.manual_calibration
Control panel key(s):
Hold
PAUSE
 +
CANCEL
 for 2 seconds to initiate calibration.
Printer web page:
The calibration procedure cannot be initiated through the web pages. See the following web page for settings that are set during sensor calibration:
View and Modify Printer Settings
Calibration
Do not change these settings unless you are told to do so by Zebra Technical Support or by an authorized service technician.
Communication Diagnostics Mode
Use this diagnostics tool to cause the printer to output the hexadecimal values for all data received by the printer.
For more information, see Communication Diagnostics Test.
Accepted values:
  • DISABLED
  • ENABLED
Related ZPL command(s):
~JD
 to enable
~JE
 to disable
SGD command used:
device.diagnostic_print
Control panel key(s):
Hold
PAUSE
 +
FEED
 for 2 seconds when the printer is in the Ready state.