1. PS30 Product Reference Guide
  2. Accessories
  3. Accessories for Charging
  4. 3-Slot Cradle
  5. Setup
  6. Mounting the 3-Slot Cradle on a Dispenser Wall
  • PS30 Personal Shopper Product Reference Guide
Mounting the 3-Slot Cradle on a Dispenser Wall

Mounting the 3-Slot Cradle on a Dispenser Wall

The 3-slot cradle can be bolted to a dispenser wall or to any supporting furniture using eight mounting holes. The back cover of the cradle has two access holes for routing power cables to/from a power supply unit or adjacent cradle.
DO NOT connect more than four cradles to a single power supply unit when in standard charging mode or three cradles when in fast charging mode. DO NOT connect the power supply unit to a power outlet until all installation steps are completed.
This procedure is an example installation of 3-slot cradles in fast charging mode, high-density configuration.
  1. Use the wall mount template to plan and mark the screw locations on the dispenser wall.
  2. In all cradles, plug the power extension cable (p/n CBL-MC18-EXINT1-01) into the free connector on the left slot.
  3. Plug the interconnect cable (p/n 25-66431-01R) into the free connector on the right slot.
    Three Slot Cradle - Cable Connections
    1
    Interconnect Cable (p/n 25-66431-01R)
    2
    Cradle Interconnection Extension Cable (p/Interconnect Cable n CBL-MC18-EXINT1-01)
  4. On all of the back covers, knock out the stamped access hole(s).
  5. Route the interconnect cables through the access holes in the back covers.
    Three Slot Cradle - Back Cover Cable Routes
  6. Secure the back cover of each cradle using six T10 Torx screws (supplied). Torque screws to 6 Kgf-cm (5.2 in-lb).
    Three Slot Cradle - Securing the Back Cover
  7. Insert the front cover removal tool into the two slots on the back of a cradle. Lever upwards and pull to remove the front cover from the cradle.
    Three Slot Cradle - Removing Front Cover
  8. Position the cradle on the dispenser wall and route all interconnect cables through the access holes in the dispenser wall.
  9. Fasten the cradle to the wall using eight screws (not supplied). Make sure to use additional wall mounting hardware, as needed, for safe mounting, according to the wall type.
    Three Slot Cradle - Fastening the Cradle to a Wall
  10. Insert the tabs on the upper side of the front cover into the slots on the cradle. Then rotate the cover down until it snaps into place.
    Three Slot Cradle - Connecting the Front Cover
  11. Connect the cables and power supply as shown.
    1. Plug the Power Extension Cable (p/n CBL-MC18-EXINT1-01) to the interconnect cable (p/n 25-66431-01R).
    2. Plug the “Y” cable (CBL-DC-392A1-02) to the Interconnect cables (p/n 25-66431-01R).
    3. Plug the “Y” cable (CBL-DC-392A1-02) to the power supply unit.
    4. Secure the power supply unit (p/n PWR-BGA12V108W0WW) to the back of the dispenser wall.
    5. Connect the power cord to the power supply unit and to a 110/220 VAC outlet.
    1
    Power extension cable (p/n CBL-MC18-EXINT1-01)
    2
    Power extension cable (p/n CBL-MC18-EXINT1-01)
    3
    Interconnect cable (p/n 25-66431-01R)
    4
    Cradle interconnection extension cable (p/n CBL-MC18-EXINT1-01)
    5
    DC “Y” charging cable long (CBL-DC-392A1-02)
    6
    Power supply unit (PWR-BGA12V108W0WW)
  12. Place the socket onto the cradle and secure the four screws.
  13. Place the socket cover onto the cradle and secure the two screws.