1. Zebra 4Sight XV7 Product Reference Guide
  2. Technical Reference
  • Zebra 4Sight XV7 Product Reference Guide
Technical Reference

Technical Reference

This section summarizes the key features of the Zebra 4Sight XV7 unit. In addition, this appendix provides descriptions for external and internal connectors of the Zebra 4Sight XV7 unit.

Motherboard

  • Micro-ATX based form factor.
  • One of the following processors:
    - Intel i5-14501-E
    - Intel i7-14700
    - Intel i9-14900
  • Intel Platform Controller Hub (PCH) 680E chipset.
  • Supports up to four devices, which can be connected to the available video output connectors: HDMI, DisplayPort, and VGA. The video output connectors support the following maximum resolutions:
    Connector
    Maximum resolution
    VGA
    1920 x 1200 @ 60 Hz
    HDMI version 2.0a
    4096 x 2160 @ 24 Hz
    DP
    4096 x 2304 @ 60 Hz
  • Four Gigabit Ethernet interfaces that use standard RJ-45 Ethernet connectors1. Three use an I226-V Gigabit Ethernet controller, and oner uses a I226-LM controller. Each supports 2.5GbE connections.
  • Ten USB interfaces. There are two USB 2.0 connectors on the front of the unit and eight USB 3.2 connectors on the back, four of which are Gen 2 and 4 are Gen 1. Inside the unit on the motherboard, there are two USB 2.0 headers2 and one USB 3.2 header, each of which support two USB ports per header.
  • One serial port connector on the outside of the unit; you can connect a device through either the RS-232, RS-422, or RS-485 standard. There are also three additional RS-232 serial port headers available on the motherboard inside the unit.
  • Support for stereo audio output, and a microphone.
  • Four PCIe 4.0 slots:
    Slot #
    Description
    1
    PCIe 4.0 x163 (only x8 if slot 3 is used)
    2
    PCIe 4.0 x4 (open-ended)
    3
    PCIe 4.0 x16
    a
     (electrically x16)
    4
    PCIe 4.0 x4 (open-ended)
  • Three M.2 sockets. One is E-Key with support for PCIe x1, CNVI, and USB 2.0 for wireless. Two are M-Key and the one closest to the CPU is used to connect the 256 Gbytes NVME SSD.
  • Four 288-pin UDIMM slots supporting dual-memory channel DDR5-4400 MHz RAM (ECC/Non-ECC. Each slot supports a memory module up to 192 Gbytes in size.
  • Four SATA3 data connectors. One SATA3 data connector is shared with the M.2 M-Key socket.

Memory

Zebra 4Sight XV7 supports UDIMM DDR5 SDRAM. Zebra 4Sight XV7 ships with either two or four 16-Gbyte DDR5 SDRAM modules that are non-ECC and run at up to 5600 Mbps.

Default Storage Drive

  • M.2 NVME SSD.
  • Storage capacity: 256 Gbytes.
Drive specifications are subject to change without notice.

Fans

The fans, which are used to cool the unit, operate at speeds controlled by the on-board fan controller, based on the temperatures of the processor and the motherboard.
When the unit is first turned on, or restarted, the fans will initially operate at their maximum speed.

Air Filter

The Zebra 4Sight XV7 unit contains a polyurethane air filter. The air filter will need to be cleaned on a regular basis. If you operate your Zebra 4Sight XV7 in a dusty environment, you might notice that the unit is overheating, or that the fan is running faster and noisier than usual. These are indicators that the filter needs to be cleaned. For information on how to clean it, see the Cleaning the air filter and adding devices to Zebra 4Sight XV7 section.
1 PoE is not supported on either Ethernet connector.
2 The external 2.0 USB connectors are connected to one of the internal USB 2.0 headers.
3 The first PCIe 4.0 x16 connector (slot 1) will operate at a x8 width when a board is present in the second PCIe 4.0 x16 connector (slot 3). The second PCIe 4.0 x16 connector (slot 3) is electrically wired as a PCIe x8 slot, so PCIe x16 boards will operate at a maximum of PCIe x8.