Network Setting | Description | |
---|---|---|
Active Print Server | Informs you of the presence of an active server. Only one print server can be installed at a time, therefore the print server installed is the active print server. SGD: ip.active_network | ![]() |
Primary Network | View or modify whether the wireless print server is considered primary. You may select which one is primary. SGD: ip.primary_network For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
WLAN IP Address | View, and if necessary, change the printer’s WLAN IP address. SGD: wlan.ip.addr For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
WLAN Subnet Mask | View, and if necessary, change the WLAN subnet mask. SGD: wlan.ip.netmask For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
WLAN Gateway | View, and if necessary, change the default WLAN gateway. SGD: wlan.ip.gateway For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
WLAN IP Protocol | This parameter tells if you (permanent) or the server (dynamic) selects the WLAN IP address. SGD: wlan.ip.protocol For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
WLAN MAC Address | View the WLAN Media Access Control (MAC) address of the wireless print server that is installed in the printer. SGD: wlan.mac_addr | ![]() |
ESSID | The Extended Service Set Identification (ESSID) is an identifier for your wireless network. This setting, which cannot be modified from the control panel, gives the ESSID for the current wireless configuration. SGD: wlan.essid For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
AP MAC Address | View the AP MAC address associated with the printer. SGD: wlan.bssid | ![]() |
Channel | View the wireless channel being used when the wireless network is active and authenticated. SGD: wlan.channel | ![]() |
Signal | View the wireless signal strength when the wireless network is active and authenticated. SGD: wlan.signal_strength | ![]() |
Wired IP Address | View, and if necessary, change the printer’s wired IP address. SGD: internal_wired.ip.addr For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Wired Subnet Mask | View, and if necessary, change the printer’s wired subnet mask. SGD: internal_wired.ip.netmask For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Wired Gateway | View, and if necessary, change the wired gateway setting. SGD: internal_wired.ip.gateway For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Wired IP Protocol | This parameter tells if you (permanent) or the server (dynamic) selects the IP address. If a dynamic option is chosen, this parameter tells the method(s) by which the wired or wireless server receives the IP address from the server. SGD: internal_wired.ip.protocol For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Wired MAC Address | View, and if necessary, change the printer’s network signal. SGD: internal_wired.mac_addr | ![]() |
IP Port | This printer setting refers to the internal wired print servers port number that the TCP print service is listening on. Normal TCP communications from the host should be directed to this port. SGD: ip.port For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
IP Alternate Port | This command sets the port number of the alternate TCP port. SGD: ip.port_alternate For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Print Information | Print the specified information on one or more labels. This menu item is available through three user menus with different default values for each. SGD: device.user_vars.display_ wmlsgd_printlist | ![]() |
Reset Network | This option resets the wired or wireless print server and saves any changes that you made to any network settings. For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Visibility Agent | When the printer is connected to a wired or wireless network, it attempts to connect to Zebra’s Asset Visibility Service via the Cloud-based Zebra Printer Connector using an encrypted, certificate-authenticated web socket connection. The printer sends Discovery Data and Settings and Alerts Data. Data printed via any label format is NOT transmitted. To opt out of this feature, disable this setting. SGD: weblink.zebra_connector. enable For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |
Load Defaults | Restore specific printer, print server, and network settings back to the factory defaults. Use care when loading defaults because you need to reload all settings that you changed manually. This menu item is available through two user menus with different default values for each. SGD: ezpl.load_defaults For printers with Protected Mode enabled, you cannot modify this setting from the front panel. For more information, refer to the Zebra Link-OS PrintSecure Printer Administration Guide. | ![]() |