Solutions
Hardware
Software
Services
Support and Downloads
About Zebra
ZQ610 Plus / ZQ620 Plus / ZQ630 Plus User Guide
Using the Printer
Creating Labels
Label Design Considerations
Black Mark Dimensions (Receipt Media)
ZQ610 Plus/ZQ620 Plus/ZQ630 Plus User Guide
ZQ610 Plus/ZQ620 Plus/ZQ630 Plus User Guide
Introduction
Printing Technology
Healthcare Printers (ZQ610 Plus-HC/ZQ620 Plus-HC)
QR Code and Support Page URL
Components
Basic Drawing and Information about Parts
Control Panel
Power-up and Runtime Sequences
Sleep Mode
Draft Mode
Navigating through Screens in the Printer Display
Idle Display, Home Menu, and User Menus
Status Icons
Status Lights
Getting Started
Unpacking and Inspection
Unpacking and RMA
Ordering Supplies and Accessories
Accessories
Installing Drivers and Connecting to a Windows-Based Computer
Installing the Drivers
Running the Printer Installation Wizard
What to Do If You Forget to Install Printer Drivers First
Zebra Setup Utilities
Adding a Printer through Zebra Setup Utilities
Cable Connection
Cable Communication
Providing Strain Relief for Communication Cables
Using Batteries
Battery Safety
Extending Battery Life
Removing the Battery
Removing the Battery Tape Insulator
Installing the Battery
Battery Charging and Cradles
Charging the Battery
Charger Safety
Smart Charger 2 - Single Battery Charger
Smart Charger 2 - Charging Status Indicators
Smart Charger 2 - Battery Health Indicator
Quad Charger
Using the Quad Charger
Quad Charger Status Indicators
Ethernet and Charging Cradle
Printer Operation with Cradle
1-Slot Battery Charger
3-Slot Battery Charger
1- and 3-Slot Battery Charger Status Indicators
Loading Media
Loading Media in Tear-Off Mode
Loading Media in Peel-Off Mode (ZQ610 Plus/ZQ620 Plus)
Loading Media in Peel-Off Mode (ZQ630 Plus)
Printing a Test Label
Wearing the Printer
Swivel Belt Clip
Metal Belt Clip
Adjustable Shoulder Strap
Soft Case
Hand Strap
Hard Case
Waist Holster
Configuring the Printer
Changing Printer Settings - User Menus
Settings Menu
Tools Menu
Network Menu
RFID Menu
Language Menu
Sensors Menu
Communications Menu
Bluetooth Menu
Battery Menu
RFID Calibration
RFID Calibration Process
Using the Printer
Creating Labels
Using Label Design Content
Using ZPL/CPCL/EPL Commands
Label Design Considerations
Using Pre-Printed Receipt Media
Black Mark Dimensions (Receipt Media)
Label Areas
Label Design Examples
Keep-Out Areas
Wireless Communications with Bluetooth
Bluetooth Networking Overview
Bluetooth Security Modes
Bluetooth Minimum Security Modes
WLAN Overview
Print Touch/NFC
NFC Use Cases
Radio Frequency Identification (RFID)
Maintaining the Printer
Recommended Cleaning Schedule
Cleaning the Linerless Printer (ZQ610 Plus/ZQ620 Plus)
Cleaning the Linerless Printer (ZQ630 Plus)
Troubleshooting
Contacting Technical Support
Error Indicators
Error Messages
Printing a Configuration Label
Configuration Label Example
Troubleshooting Issues
Communication Issues
Specifications
Printer Specifications
Power Specifications
Communication Interface Specifications
Media Specifications
ZPL Font and Barcode Specifications and Commands
CPCL Font and Barcode Specifications and Commands
Communication Ports
Black Mark Dimensions (Receipt Media)
Black Mark Dimensions (Receipt Media)
The reflective media black marks (or black bar/marks) should extend past the centerline of the roll on the front side of the paper.
Minimum mark width: 15 mm (0.59 in.) perpendicular to the edge of the media, and centered within the width of the roll.
Mark length: 4.8–6.0 mm (0.19–0.24 in.) parallel to the edge of the media.
Label Design Considerations
