Setting | Description, Accepted Values, and Configuration Methods |
|---|---|
ACTIVE PRINT SERVER  | View whether the WIRED or WIRELESS print server is currently active. |
PRIMARY NETWORK  | View or modify whether the WIRED or WIRELESS print server is considered primary. You may select which one is primary. Accepted values:
SGD command used: ip.primary_network |
WIRED IP ADDRESS  | View and, if necessary, change the printer’s Wired IP Address. To save changes to this setting, set WIRED IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used: internal_wired.ip.addr Print Server web page: |
WIRED SUBNET MASK  | View and, if necessary, change the wired subnet mask. To save changes to this setting, set WIRED IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used: internal_wired.ip.netmask Print Server web page: |
WIRED GATEWAY  | View and, if necessary, change the default wired gateway. To save changes to this setting, set WIRED IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used: internal_wired.ip.gateway Print Server web page: |
WIRED IP PROTOCOL  | This parameter indicates if the Net Administrator/User (permanent) or the server (dynamic) selects the Wired print server’s IP address. When a dynamic option is chosen, this parameter tells the method(s) by which this print server receives the IP address from the server. The print server must be reset to allow changes to the network settings to take effect. Accepted values:
Related ZPL command(s): ^ND SGD command used: internal_wired.ip.protocol Print Server web page: |
WIRED MAC ADDRESS  | View the Media Access Control (MAC) address of the wired print server. SGD command used: internal_wired.mac_addr Print Server web page: |
WLAN IP ADDRESS  | View and, if necessary, change the printer’s Wireless IP address. To save changes to this setting, set WLAN IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used:
Print Server web page: |
WLAN SUBNET MASK  | View and, if necessary, change the Wireless subnet mask. To save changes to this setting, set WLAN IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used: Print Server web page: |
WLAN GATEWAY  | View and, if necessary, change the default wireless gateway. To save changes to this setting, set WLAN IP PROTOCOL to PERMANENT, and then reset the print server (see RESET NETWORK in this table). Accepted values: 000 to 255 for each field Related ZPL command(s): ^ND SGD command used: wlan.ip.gateway Print Server web page: |
WLAN IP PROTOCOL  | This parameter indicates if the Net Administrator/User (permanent) or the server (dynamic) selects the Wireless print server’s IP address. When a dynamic option is chosen, this parameter tells the method(s) by which this print server receives the IP address from the server. Important • The print server must be reset to allow changes to the network settings to take effect. Accepted values:
Related ZPL command(s): ^ND SGD command used: wlan.ip.protocol Print Server web page: |
WLAN MAC ADDRESS
 | View the Media Access Control (MAC) address of the wireless print server. SGD command used: wlan.mac_addr Print Server web page: |
ESSID  | The Extended Service Set Identification (ESSID) is an identifier for your wireless network. This setting, which cannot be modified from the user interface, gives the ESSID for the current wireless configuration. Accepted values: 32-character alphanumeric string (default 125) SGD command used: wlan.mac_addr Print Server web page: |
CHANNEL  | View the wireless channel being used when the wireless network is active and authenticated. SGD command used: wlan.channel Print Server web page: Print Server web page: |
SIGNAL  | View the wireless signal strength when the wireless network is active and authenticated. SGD command used: wlan.signal_strength Print Server web page: |
IP PORT  | This printer setting refers to the internal wired print servers port number that the TCP print service is listening on. Normal TCP communications from the host should be directed to this port. SGD command used: internal_wired.ip.port Print Server web page: |
IP ALTERNATE PORT
 | This command sets the port number of the alternate TCP port. SGD command used: internal_wired.ip.port_alternate Print Server web page: Print servers supporting this command will simultaneously monitor both primary and alternate ports for connections. |
RESET NETWORK  | Used to reset the wired or wireless print server and saves any changes that you made to any network settings. When you change any network settings, the printer's internal print server must be reset for the changes to take effect. Related ZPL command(s): ~WR SGD command used: device.reset Print Server web page: |
VISIBILITY AGENT  | When the printer is connected to a wired or wireless network, it will attempt to connect to Zebra’s Asset Visibility Service via the Cloud-based Zebra Printer Connector using an encrypted, certificate-authenticated web socket connection. The printer sends Discovery Data and Settings and Alerts Data. Data printed via any label formats is NOT transmitted. To opt out of this feature, disable this setting. For more information, see the "Disabling the Visibility Agent" Application Note at zebra.com/support. Accepted values:
SGD command used: weblink.zebra_connector.enable Print Server web page: |
