Checkstand Counter Cutouts and MP72 Dimensions

MP72 Scanner Scale Integrator Guide

There are three sets of dimensions for counter cutouts based on the MP72 configuration to install. Ensure cut edges are clean and straight, with all burrs and splinters removed.

The MP72 is 11.5 in. wide. If replacing an existing scanner in a checkstand that is 12 in. wide, using a Trim Filler Kit is recommended to fill the gap in the checkstand (see Trim Kit Installation (If Required)).

The MP72 is 4 in. deep. If replacing an existing 5 in. deep short or medium scanner, you must use the 1 in. longer leveling screw kit (p/n MX302-SR00004ZZWR) to bring the platter up to the countertop level.

Cutout/Dimensions - MP72 Short Configuration

Short Configuration (No Scale) Counter Cutout

Item	Description
1	356.2 ±1.5 mm / 14.03 ±0.06 in.
2	Max R 6.35 mm / 0.25 in.; 2x cashier side
3	Max 6.4 mm / 0.25 in.
4	Optional leveling feet locations
5	Max 101.6 mm / 4.0 in.
6	295.3 ±1.5 mm / 11.63 ±0.06 in.

Short Configuration (No Scale) Top View Dimensions

Item	Description
1	292.0 mm / 11.50 in.
2	350.9 mm / 13.81 in.

Short Configuration (No Scale) Side View Dimensions

Item	Description
1	356.2 ±1.5 mm / 14.03 ±0.06 in. (counter opening)
2	128.0 mm / 5.04 in.
3	101.0 mm / 3.98 in.
4	Optional leveling screw kit: MX301-SR00004ZZWR or MX302-SR00004ZZWR

Short Configuration (No Scale) Front View Dimensions

Item	Description
1	44.5 ±6.6 mm / 1.75 ±0.25 in.
2	Support rails

Use the support rails as shown, and not a shelf. If liquid spills it pools on a shelf.

Cutout/Dimensions - MP72 Medium Configuration

Item	Description
1	402.0 ±1.5 mm / 15.83 ±0.06 in.
2	Max R 6.35 mm / 0.25 in.; 2x cashier side
3	Max 50.8 mm / 0.25 in.
4	Optional leveling feet locations
5	Max 101.6 mm / 4.0 in.
6	295.3 ±1.5 mm / 11.63 ±0.06 in.

Medium Configuration Top View Dimensions

Item	Description
1	292.0 mm / 11.50 in.
2	397.9 mm / 15.66 in.

Medium Configuration Side View Dimensions

Item	Description
1	402.0 ±1.5 mm / 15.83 ±0.06 in. (counter opening)
2	128.0 mm / 5.04 in.
3	101.0 mm / 3.98 in.
4	Optional leveling screw kit: MX301-SR00004ZZWR or MX302-SR00004ZZWR

Leveling screws accessory kit MX301-SR00004ZZWR is shipped with every short and medium configuration. Longer leveling screws with a 25 mm (1 in.) extra length are available for purchase, if required (accessory kit p/n MX302-SR00004ZZWR).

Medium Configuration Front View Dimensions

Item	Description
1	44.5 ±6.6 mm / 1.75 ±0.25 in.
2	Support rails

Use the support rails as shown, and not a shelf where spilled liquid can pool.

Cutout/Dimensions - MP72 Long Configuration

Item	Description
1	511.2 ±1.5 mm / 20.13 ±0.06 in.
2	Min 19.1 mm / 0.75 in. Max 42.0 mm / 1.65 in. Max 31.0 mm / 1.22 in. (cashier side)
3	295.3 ±1.5 mm / 11.63 ±0.06 in.
4	Max 473.1 mm / 18.63 in.
5	Typical checkstand leveling screw locations

Item	Description
1	292.2 mm / 11.50 in.
2	505.7 mm / 19.90 in.

Item	Description
1	511.2 ±1.5 mm / 20.13 ±0.06 in. (counter opening)
2	128.5 mm / 5.06 in. (counter to top of unit)
3	100.6 mm / 3.96 in. (counter to bottom of unit)
4	10.0 ±0.8 mm / 0.39 ±0.03 in.
5	Max 473.1 mm / 18.63 in.

After routing, the countertop must have sufficient strength to support the scanner and the loads placed on top of it. If required, add strengthening supports underneath the countertop.