1. ZPL II, ZBI 2, Set-Get-Do, Mirror, WML Programming Guide
  2. SGD Wireless Commands
  3. wlan.security
  4. Supporting SGDs for Different Security Types
  • ZPL II, ZBI 2, Set-Get-Do, Mirror, WML Programming Guide
Supporting SGDs for Different Security Types

Supporting SGDs for Different Security Types

The supporting SGD commands required for
wlan.security
 vary based on the security type that you select. You must send the additional commands for your printer to be able to work on your wireless network. Follow the example and format for your specific security type in this section, substituting your own wireless network data.

Security Type 1: No Wireless Security Active

Additional parameters that need to be set: none
Example
This example turns off all wireless securities controlled under this command, but it does not reset the printer’s wireless settings to their defaults. 
! U1 setvar "wlan.security" "1"

Security Type 2: WEP 40-Bit

Additional parameters that need to be set and the SGD commands to use:
  • WEP encryption index (see
    wlan.wep.index
    )
  • WEP authentication type (see
    wlan.wep.auth_type
    )
  • WEP key type (see
    wlan.wep.key_format
    )
  • the actual values of any WEP encryption keys to be used (see
    wlan.wep.key1
    ,
    wlan.wep.key2
    ,
    wlan.wep.key3
    , or
    wlan.wep.key4
    )
Example
This example configures the printer for WEP 40-bit encryption using index key 1, open authentication, and a hexadecimal WEP key with a value of
“A1B2C3D4F5”
. 
! U1 setvar "wlan.security" "2"
! U1 setvar "wlan.wep.index" "1"
! U1 setvar "wlan.wep.auth_type" "open"
! U1 setvar "wlan.wep.key_format" "hex"
! U1 setvar "wlan.wep.key1" "A1B2C3D4F5"

Security Type 3: WEP 128-Bit

Additional parameters that need to be set and the SGD commands to use:
  • WEP encryption index (see
    wlan.wep.index
    )
  • WEP authentication type (see
    wlan.wep.auth_type
    )
  • WEP key type (see
    wlan.wep.key_format
    )
  • the actual values of any WEP encryption keys to be used (see
    wlan.wep.key1
    ,
    wlan.wep.key2
    ,
    wlan.wep.key3
    , or
    wlan.wep.key4
    )
Example
This example configures the printer for WEP 128-bit encryption using index key 2, open authentication, and four hexadecimal WEP keys.
! U1 setvar "wlan.security" "3"
! U1 setvar "wlan.wep.index" "2"
! U1 setvar "wlan.wep.auth_type" "open"
! U1 setvar "wlan.wep.key_format" "hex"
! U1 setvar "wlan.wep.key1" "001122334455667788"
! U1 setvar "wlan.wep.key2" "112233445566778899"
! U1 setvar "wlan.wep.key3" "223344556677889900"
! U1 setvar "wlan.wep.key4" "334455667788990011"

Security Type 4: EAP-TLS

Additional parameters that need to be set and the SGD commands to use:
  • optional private key password (see
    wlan.private_key_password
    )
Example
This example configures the printer for EAP-TLS authentication with an optional private key password with a value of “
private
.”
! U1 setvar "wlan.security" "4"
! U1 setvar "wlan.private_key_password" "private"

Security Type 5: EAP-TTLS

Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
With a value of
"user"
 and a password with a value of
"password"
.
! U1 setvar "wlan.security" "5"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 6: EAP-FAST

Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
  • optional private key password (see
    wlan.private_key_password
    )
Example
This example configures the printer for EAP-FAST authentication, including a user ID of
"user"
, a password of
"password"
, and an optional private key of
"private"
.
! U1 setvar "wlan.security" "6"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"
! U1 setvar "wlan.private_key_password" "private"

Security Type 7: PEAP

Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
This example configures the printer for PEAP authentication, including a user ID with a value of
"user"
 and a password with a value of
"password"
.
! U1 setvar "wlan.security" "7"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 8: LEAP

Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
This example configures the printer for LEAP authentication, including a user ID with a value of
"user"
 and a password with a value of
"password"
.
! U1 setvar "wlan.security" "8"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 9: WPA PSK

Configuring the printer for WPA also allows the printer to be used in WPA2 environments. Key rotation for WPA2 PSK is supported in firmware version 60.15.8Z and later and in firmware version 53.15.8Z and later.
Additional parameters that need to be set and the SGD commands to use:
  • Pre-Shared Key (PSK) value (see
    wlan.wpa.psk
    )
Example
This example configures the printer for WPA PSK authentication with a PSK value of all zeroes (64 hexadecimal digits).
! U1 setvar "wlan.security" "9"
! U1 setvar "wlan.wpa.psk" "00000000..."

Security Type 10: WPA EAP-TLS

Configuring the printer for WPA also allows the printer to be used in WPA2 environments.
Additional parameters that need to be set and the SGD commands to use:
  • optional private key password (see
    wlan.private_key_password
    )
Example
This example configures the printer for WPA EAP-TLS authentication with an optional private key password with a value of
"private"
.
! U1 setvar "wlan.security" "10"
! U1 setvar "wlan.private_key_password" "private"

Security Type 11: WPA EAP-TTLS

Configuring the printer for WPA also allows the printer to be used in WPA2 environments.
Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
This example configures the printer for WPA EAP-TTLS authentication, including a user ID with a value of
"user"
” and a password with a value of
"password"
.
! U1 setvar "wlan.security" "11"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 12: WPA EAP-FAST

Configuring the printer for WPA also allows the printer to be used in WPA2 environments.
Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
  • optional private key password (see
    wlan.private_key_password
    )
Example
This example configures the printer for WPA EAP-FAST authentication, including a user ID of
"user"
, a password of
"password"
, and an optional private key of
"private"
.
! U1 setvar "wlan.security" "12"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"
! U1 setvar "wlan.private_key_password" "private"

Security Type 13: WPA PEAP

Configuring the printer for WPA also allows the printer to be used in WPA2 environments.
Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
This example configures the printer for WPA PEAP authentication, including a user ID with a value of
"user"
 and a password with a value of
"password"
.
! U1 setvar "wlan.security" "13"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 14: WPA LEAP

Configuring the printer for WPA also allows the printer to be used in WPA2 environments.
Additional parameters that need to be set and the SGD commands to use:
  • user ID (see
    wlan.username
    )
  • password (see
    wlan.password
    )
Example
This example configures the printer for WPA LEAP authentication, including a user ID with a value of
"user"
 and a password with a value of
"password"
.
! U1 setvar "wlan.security" "14"
! U1 setvar "wlan.username" "user"
! U1 setvar "wlan.password" "password"

Security Type 15: Kerberos

Additional parameters that need to be set and the SGD commands to use:
  • Kerberos user ID (see
    wlan.kerberos.username
    )
  • Kerberos password (see
    wlan.kerberos.password
    )
  • realm (see
    wlan.kerberos.realm
    )
  • Key Distribution Center (KDC) (see
    wlan.kerberos.kdc
    )
Example
This example configures the printer for Kerberos encryption, including a Kerberos user ID with a value of
"user"
, a Kerberos password with a value of
"password"
, a realm of
"zebra"
, and a KDC of
"krbtgt"
.
! U1 setvar "wlan.security" "15"
! U1 setvar "wlan.kerberos.username" "user"
! U1 setvar "wlan.kerberos.password" "password"
! U1 setvar "wlan.kerberos.realm" "zebra"
! U1 setvar "wlan.kerberos.kdc" "krbtgt"